Keyless Ignition fitted to my H2 SX SE

Bike aesthetic/mechanical/electrical modifications and general wrenching advice.
User avatar
Champ87
Supercharged!

Supercharged!
Posts: 1289
Joined: Mon Apr 09, 2018 1:43 am
Location: NW Indiana US
Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
x 304
x 554

Keyless Ignition fitted to my H2 SX SE

Post by Champ87 » Thu Mar 21, 2019 1:03 pm


When I first got my SE something I missed was the keyless ignition system like the one I’d fitted to my Triumph Sprint a few years earlier. OK, I wasn’t losing sleep over it, but being able to walk up to the bike and power up without a key becomes so natural that it’s easy to forget how convenient it is – until you don’t have it.

All good now though: a winter project added a keyless system to my H2 SX SE. Here’s a video clip showing it in operation:

0 x

Champ87
It's amazing how fast you can go when you take your time.

User avatar
Champ87
Supercharged!

Supercharged!
Posts: 1289
Joined: Mon Apr 09, 2018 1:43 am
Location: NW Indiana US
Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
x 304
x 554

Re: Keyless Ignition fitted to my H2 SX SE

Post by Champ87 » Thu Mar 21, 2019 1:04 pm


Use
Simply walk up to the bike with remote in pocket, turn signals will flash, kill switch on, pull the clutch lever and start. Easy eh? Moving the kill switch to the “Off” position will shut everything down. Pulling the clutch lever brings it all back to life – provided the remote is still in range. The system will not activate once the remote is taken out of range. Alternatively, the system can be manually armed or disarmed by pressing the button on the remote.

Of course, a key is still needed to unlock the gas cap, seat or hard bags but, for ignition, the key stays in my pocket attached to the remote.

Configuration
The system was put together by my friend DEcosse from the triumphrat.net forum. Over the years he’s put together dozens of them, most for fellow Triumph owners (including the one on my Sprint). He’s improved and refined the system to the point where it’s now a completely solid-state system using a proven and reliable commercial RFID receiver. It has integrated power, control and immobilizer function all contained in a water-resistant enclosure that measures 8.5 cm x 8.5 cm (3.3” x 3.3”).

A surprising amount of planning and development work was needed to create a system that would work on the Kawasaki. Fortunately, DEcosse did all the clever thinking to overcome some of the obstacles the H2 SX SE presented and incorporated that into the electronics. The final configuration was developed, installed and tested on an H2 SX SE – mine.

Installation

Normally, installation would be pretty much ‘plug-n-play’. I would guess maybe 1 - 2 hours work plus the time it takes to remove and refit fairing panels. However, with mine being the first H2 SX SE system, a lot of extra time was required to figure out how to route the wiring. The Keyless Controller uses an OEM connector to plug directly into the harness in place of the Ignition Key Switch. There are also 4 signal/trigger connections required for the system to work. One of those connections uses a Posi-Tap connector. For the others, OEM connectors provide direct connection to the original wiring with no cutting or soldering.
0 x

Champ87
It's amazing how fast you can go when you take your time.

User avatar
Champ87
Supercharged!

Supercharged!
Posts: 1289
Joined: Mon Apr 09, 2018 1:43 am
Location: NW Indiana US
Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
x 304
x 554

Re: Keyless Ignition fitted to my H2 SX SE

Post by Champ87 » Thu Mar 21, 2019 1:11 pm


Other
One problem we encountered was the sidestand lockout preventing keyless ignition with the sidestand down. It’s a limitation of the Kawasaki system for which the alternative is to bypass the sidestand switch. At first, I wasn’t comfortable with that until I reminded myself that I rode for 35 years before sidestand lockout became a thing. I figured that maybe I was being too cautious and opted to bypass the switch.

With the keyless system in place the original key switch could be removed. I left mine in place, simply because I couldn’t be arsed to remove it and it does provide a small amount of protection as a steering lock. Since I don’t need access to insert the key there’s a little extra space around the top clamp for mounting my GPS.

When I first installed a keyless system on my Triumph Sprint I wondered about reliability. I don’t know why; for many years I’ve had cars with keyless systems and never questioned the reliability or experienced any problems. The system on my Sprint worked without fault from the time I installed it until I sold the bike 3 years later.

Installation includes a status LED to indicate when the system is ready. It’s optional but I omitted it from my Triumph setup and regretted it. The LED comes on when the remote is detected and, to avoid distraction while riding, it goes off when the ignition is switched on. Looking at it now, I think using a Green LED to indicate 'Ready' might have been better but I went with Red.

Another option is the ‘Chirp’ module. A little piezo alarm provides an audible alert to supplement the flashing turn signals when the system is armed or disarmed. When walking away from the bike it’s nice to have that confirmation that the system is armed without looking back to see that the turns flashed when the remote went out of range.

This system can be built with an additional power supply – a switched output for accessories. I decided not to go with that option.
0 x

Champ87
It's amazing how fast you can go when you take your time.

User avatar
Raddy47
Accelerating

Accelerating
Posts: 212
Joined: Sun Mar 10, 2019 11:55 pm
x 1

Re: Keyless Ignition fitted to my H2 SX SE

Post by Raddy47 » Thu Mar 21, 2019 10:30 pm


I hate keyless stuff. But props to you for putting in the time and effort. Lots of people are going to love this. Again good work!
0 x

User avatar
Burmashave
Supercharged!

Supercharged!
Posts: 542
Joined: Mon Jul 16, 2018 8:59 pm
Location: USA
Bike(s): H2 SX SE
x 16
x 11

Re: Keyless Ignition fitted to my H2 SX SE

Post by Burmashave » Thu Mar 21, 2019 11:50 pm


Good work and good detail in the write up, Champ. Like Raddy, I doubt I'd go that route, but I can see why you did. It's a matter of what you get used to, and thinking about just that, I realize how attached I am to the keys and fobs (Kawi factory cloth fobs) for my two Kawi's.
0 x

User avatar
PaulieG
Boost Engaged

Boost Engaged
Posts: 40
Joined: Tue Nov 06, 2018 4:25 pm
Location: Northern VA
Bike(s): 2019 H2 SX SE+
x 2

Re: Keyless Ignition fitted to my H2 SX SE

Post by PaulieG » Fri Mar 22, 2019 11:37 am


If I didn't have a key where would I keep my key chain?

Image
0 x

User avatar
Champ87
Supercharged!

Supercharged!
Posts: 1289
Joined: Mon Apr 09, 2018 1:43 am
Location: NW Indiana US
Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
x 304
x 554

Re: Keyless Ignition fitted to my H2 SX SE

Post by Champ87 » Fri Mar 22, 2019 3:01 pm


I know what you mean guys. When I first saw an early version of this I was curious but not really interested. As DEcosse developed the system, it got to the point where I thought “I want that”. It’s not an essential add-on but if I justified everything on a need basis then I wouldn’t even own the SE to begin with! After having the system on my Triumph it felt a bit odd to go back to a key ignition with the Kawasaki. I can only describe it by saying imagine buying a new car and having to put a key in the lock to open doors. When did that last happen?

Using a key isn’t exactly a hardship but going to start the bike and realizing the key is still in my pocket and I’ve got to take gloves off, mess with zippers, rummage through pockets…… The first time that happened it prompted me to add keyless to my projects list. There have been a couple of posts about carrying spare keys to open the bags without taking the key out of the ignition. Not something that bothered me, but I do enjoy that benefit. I’m happy to put it out there for anyone else who might be interested.

Thanks for the compliments. Good that you can appreciate the effort even though it doesn’t appeal to you.
0 x

Champ87
It's amazing how fast you can go when you take your time.

User avatar
Icancin2u2
Boost Engaged

Boost Engaged
Posts: 98
Joined: Fri Mar 22, 2019 7:43 pm
Location: PNW
Bike(s): 2020 Kawasaki Z H2

Re: Keyless Ignition fitted to my H2 SX SE

Post by Icancin2u2 » Fri Mar 22, 2019 8:01 pm


I think it's fabulous. Definitely on the short list after I get mine. Curiosity, if you don't bypass the sidestand but use the center stand could the system still function as intended? Honestly, bypassing the sidestand is a concern for me, I am sure that I'd leave it in gear, go to start it, and have to pick it up off the floor. 🤯
0 x

User avatar
JonTheChron
Supercharged!

Supercharged!
Posts: 539
Joined: Sun Dec 10, 2017 9:00 pm
Location: Quebec
Bike(s): H2 SX SE '18
x 7
x 6

Re: Keyless Ignition fitted to my H2 SX SE

Post by JonTheChron » Fri Mar 22, 2019 9:02 pm


Very nice work.
0 x

2018 H2 SX SE (1st in Canada)
2011 Ninja 1000 (sold)
2009 Ninja 250R (sold)

User avatar
Champ87
Supercharged!

Supercharged!
Posts: 1289
Joined: Mon Apr 09, 2018 1:43 am
Location: NW Indiana US
Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
x 304
x 554

Re: Keyless Ignition fitted to my H2 SX SE

Post by Champ87 » Sat Mar 23, 2019 1:07 am


Icancin2u2 wrote: Fri Mar 22, 2019 8:01 pmCuriosity, if you don't bypass the sidestand but use the center stand could the system still function as intended?
Yes, absolutely. If you don't bypass the sidestand switch then the system works exactly as shown - provided the sidestand is up. Once ignition is on you could put the sidestand down, it's just that pulling the clutch to turn ignition on would not work with sidestand down in standard configuration. We tried to find away around it, but in the end we were stuck with what Kawasaki had given us and tricking the system into thinking the sidestand is up was the only solution.
Icancin2u2 wrote: Fri Mar 22, 2019 8:01 pmHonestly, bypassing the sidestand is a concern for me, I am sure that I'd leave it in gear, go to start it, and have to pick it up off the floor.
Starting in gear is not the issue. Even with sidestand switch bypass you cannot start the bike in gear unless you pull the clutch in. It's what happens once the engine is started that changes. With the bypass the engine will not cut out if you release the clutch in gear with the sidestand down so you lose protection against riding off with sidestand down. Having spent most of my riding life without such protection, I'll accept that risk as an alternative to starting with sidestand up.
JonTheChron wrote: Fri Mar 22, 2019 9:02 pmVery nice work.
Thanks. I'm proud of it. And big thanks to my friend DEcosse for spending many hours figuring this stuff out so it would work on the Kawasaki.
Last edited by Champ87 on Sat Mar 23, 2019 2:43 am, edited 1 time in total.
0 x

Champ87
It's amazing how fast you can go when you take your time.

Post Reply

Who is online

Users browsing this forum: Google [Bot] and 15 guests