Yoshimura Alpha Slip-on Questions

Bike aesthetic/mechanical/electrical modifications and general wrenching advice.
User avatar
dieseldad60
Accelerating

Accelerating
Posts: 133
Joined: Wed Jan 09, 2019 6:58 pm
Location: North Carolina
Bike(s): 2018 Kawasaki H2 SX SE, 2001 Ducati ST4
x 1

Yoshimura Alpha Slip-on Questions

Post by dieseldad60 » Thu Jan 31, 2019 6:47 pm


Thinking about putting on the Yoshimura Alpha Carbon slip-on. Probably won't do a flash at this point (maybe future). Was wondering if there were any installation gotcha's from anyone who had installed one? Looks very straightforward from what I can tell. No other mods required either - correct?

This is just my attempt at knowing what I am getting into before pulling the trigger. Thanks!
0 x

User avatar
Arthurgee
Supercharged!

Supercharged!
Posts: 34
Joined: Thu Jan 03, 2019 5:16 pm
Location: Aberdeen
Bike(s): H2 SX Tourer
x 2
x 1

Re: Yoshimura Alpha Slip-on Questions

Post by Arthurgee » Thu Jan 31, 2019 7:13 pm


Diesel, your correct, no other mods. I bought one tail end of last year. Easy to put on. Nothing challenging. If anything i found the rubber protection for the band around the exhaust was not the best and it didn't quite ft where the holes in the band were, but got it fitted ok in the end.
Attachments
20181006_151439.jpg
20181005_131147.jpg
0 x

User avatar
dieseldad60
Accelerating

Accelerating
Posts: 133
Joined: Wed Jan 09, 2019 6:58 pm
Location: North Carolina
Bike(s): 2018 Kawasaki H2 SX SE, 2001 Ducati ST4
x 1

Re: Yoshimura Alpha Slip-on Questions

Post by dieseldad60 » Thu Jan 31, 2019 7:24 pm


Arthurgee wrote: Thu Jan 31, 2019 7:13 pm Diesel, your correct, no other mods. I bought one tail end of last year. Easy to put on. Nothing challenging. If anything i found the rubber protection for the band around the exhaust was not the best and it didn't quite ft where the holes in the band were, but got it fitted ok in the end.
Awesome, thanks! One other question.... have you used it with the factory panniers? I am assuming no issue there but thought I'd ask anyway. BTW, I like the way it looks on your bike! More of that back wheel is seen.... :)
0 x

User avatar
Snakes709
Supercharged!

Supercharged!
Posts: 1399
Joined: Sun Aug 19, 2018 2:42 am
Location: Edmonton, AB
Bike(s): 2018 H2 SX SE
x 11
x 394

Re: Yoshimura Alpha Slip-on Questions

Post by Snakes709 » Thu Jan 31, 2019 7:41 pm


I'm installing a 3/4 system from a 2016+ ZX10R. Had the same setup on my 2015 ZX10R. Install is straight forward. If you are going with just a slipon, nothing needed.
Attachments
yoshi1.jpg
2666F223-74EC-47F1-8FDE-054A2815AA04.jpeg
0 x

2018 H2 SX/SE
-ZX10R Headers
-2016+ ZX10R Yoshimura Alpha 3/4 system
-Sprint P08 Filter
-Vcyclenut flash
-Driven block off plates
-Yager Werx Intercooler

User avatar
dieseldad60
Accelerating

Accelerating
Posts: 133
Joined: Wed Jan 09, 2019 6:58 pm
Location: North Carolina
Bike(s): 2018 Kawasaki H2 SX SE, 2001 Ducati ST4
x 1

Re: Yoshimura Alpha Slip-on Questions

Post by dieseldad60 » Thu Jan 31, 2019 8:21 pm


Thanks Snakes! Just pulled the trigger! :)
0 x

User avatar
Snakes709
Supercharged!

Supercharged!
Posts: 1399
Joined: Sun Aug 19, 2018 2:42 am
Location: Edmonton, AB
Bike(s): 2018 H2 SX SE
x 11
x 394

Re: Yoshimura Alpha Slip-on Questions

Post by Snakes709 » Thu Jan 31, 2019 9:21 pm


No problem, I just regret how I went about doing it. It's the yoshimura alpha 3/4 system for a 2016+ ZX10R which I had on my 2015 10R when I sold it. The dealership had a black Friday sale for just the slip on so I bought that. But its the CF/SS, not the SS/Ti I wanted to cut more weight down. Then I ordered the mid pipe separately which was suppose to take 3 weeks but the place the dealership orders from had a guy that got fired and never processed my order. So after 7 weeks, I was like "where the fuck is my midpipe" dealership checked and found out it was never processed. So have to wait another 3 weeks, which should be here next week as its been 2 weeks since I found that out. In the end it cost me about $200 less then if I ordered it online from the shop I always get parts from AND it would have been cf/ti. And I would have gotten it in 2 weeks.
2 x

2018 H2 SX/SE
-ZX10R Headers
-2016+ ZX10R Yoshimura Alpha 3/4 system
-Sprint P08 Filter
-Vcyclenut flash
-Driven block off plates
-Yager Werx Intercooler

User avatar
HouTexH2SX
Accelerating

Accelerating
Posts: 235
Joined: Mon Jul 23, 2018 1:27 pm
Location: Houston, Texas
Bike(s): '16 Yamaha FJR1300ES, '18 KTM Super Duke R, '20 Kawasaki Ninja 1000SX
x 1

Re: Yoshimura Alpha Slip-on Questions

Post by HouTexH2SX » Thu Jan 31, 2019 10:21 pm


I installed one on my bike as well and it looks so much better than the OEM. The rubber gasket that goes between the can and the bracket is a little fiddly but it does end up fitting well into all of the slots in the bracket if you are patient. I did find that the can is closer to the rear wheel than the stocker (only about 5/8") but does not appear to be a problem with clearance.
0 x

User avatar
Zdude
Accelerating

Accelerating
Posts: 212
Joined: Wed May 16, 2018 7:38 pm
Location: Enon, Ohio
Bike(s): 2018 H2SXSE , 2009 Buell Lightning
x 4

Re: Yoshimura Alpha Slip-on Questions

Post by Zdude » Thu Jan 31, 2019 11:45 pm


I've had the Yosh Alpha for about 1000 miles with no issues. Have run sometimes with the panniers without issue also. The sound and looks are so improved it's ridiculous IMHO. No other mods are required however, the single best mod I have made to this bike is to have Vcyclenut flash my ECM. The slip-on and the Sprint filter help somewhat but coupled with the flash is completely transforming. Now the power enhancement is significant (actually amazing) but even more is the smooth throttle response and the ability to change modes while riding along with other limits removed. Back to the Yosh can, it has no removable baffle but with the cat still in the exhaust the system has a great mellow sound that howls wonderfully when nailed wide open! Quality pipe and yes, that mounting rubber gasket is a small pain but as noted, it will fit just take a little patience.
0 x

User avatar
dieseldad60
Accelerating

Accelerating
Posts: 133
Joined: Wed Jan 09, 2019 6:58 pm
Location: North Carolina
Bike(s): 2018 Kawasaki H2 SX SE, 2001 Ducati ST4
x 1

Re: Yoshimura Alpha Slip-on Questions

Post by dieseldad60 » Fri Feb 01, 2019 4:05 pm


Thanks all! It should be here tomorrow (Saturday 2/2) but I am out of town for the weekend, so it will have to wait until next week or weekend to get installed. I believe that stock can sounds way too tame for this bike. I'll probably do the flash at some point but haven't spent enough time on it yet to really have an opinion. I do think the throttle response is a bit strange for me but I have adjusted so far. Thanks!
0 x

User avatar
darich1146
New Member

New Member
Posts: 9
Joined: Tue Apr 02, 2019 12:26 am
Location: Mesa, AZ
Bike(s): 2018 H2 SX SE

Re: Yoshimura Alpha Slip-on Questions

Post by darich1146 » Tue Apr 02, 2019 12:36 am


Hi. I'm contemplating swapping out the factory can for a Yoshi. For any of the guys who have done this as the only mod, do you experience any popping or other signs of needing fuel remapping? I would like to go with the vcyclenut flash but I think that is a ways down the road.

Thanks!
0 x

Post Reply

Who is online

Users browsing this forum: No registered users and 7 guests