And the Vcyclenut ECU tune continues to work extremely well.
Enjoying quick shift
- Thunderdawg
- Supercharged!

- Posts: 311
- Joined: Fri Feb 16, 2018 2:05 am
- Location: Central AZ
- Bike(s): 2018 Ninja H2 SX SE
- x 46
- x 6
Enjoying quick shift
I went for a short ride today to run an errand. The quick shift feature is really nice, I just need to adjust how I use it. Mostly, keeping throttle on for upshifts albeit, shift from 1 to 2 is a bit rough so far. I used clutchless shifting when I raced motocross in the early '70s, but then I closed the throttle to shift up and used clutch and throttle to down shift. New bike, new methods.
And the Vcyclenut ECU tune continues to work extremely well.
And the Vcyclenut ECU tune continues to work extremely well.
0 x
Vcyclenut: ZX-10 header, Lextek midpipe and can, Sprint P08 F1-85 air filter, PAIR valve block off plates, ECU flash, Woodcraft frame slider
Evotech radiator guard
Ohlins SD-021 steering damper & Bryan468 mounts, CL front brake pads
- Snakes709
- Supercharged!

- Posts: 1399
- Joined: Sun Aug 19, 2018 2:42 am
- Location: Edmonton, AB
- Bike(s): 2018 H2 SX SE
- x 11
- x 394
Re: Enjoying quick shift
1-2 is rough on mine as well. I use the clutch for 1-2 but quickshifter for everything else. Love the auto blip
0 x
2018 H2 SX/SE
-ZX10R Headers
-2016+ ZX10R Yoshimura Alpha 3/4 system
-Sprint P08 Filter
-Vcyclenut flash
-Driven block off plates
-Yager Werx Intercooler
- Burmashave
- Supercharged!

- Posts: 542
- Joined: Mon Jul 16, 2018 8:59 pm
- Location: USA
- Bike(s): H2 SX SE
- x 16
- x 11
Re: Enjoying quick shift
I didn't think I'd care about the quick shifter at all, but I've really come to like it. In fact, when I hop back on my Versys 1K, I have to remember to clutch my shifts. On a similar note, I really like the reduced engine brake setting as well.
I find that up and down shifts above 3-4K RPM's seem to go most smoothly, and upshifts in the high RPM range go very smoothly. On all my bikes, I have tended to wind it out in low gear and then short shift up. This works great without the clutch on the H2 provided I'm still accelerating slightly as I'm banging it up from 2-6.
I find that up and down shifts above 3-4K RPM's seem to go most smoothly, and upshifts in the high RPM range go very smoothly. On all my bikes, I have tended to wind it out in low gear and then short shift up. This works great without the clutch on the H2 provided I'm still accelerating slightly as I'm banging it up from 2-6.
0 x
Re: Enjoying quick shift
How would you compare leaning over on the h2 to the versys 1k? I also have a v1k looking at getting the SX once I get my 2 bikes sold. However some of my enthusiasm was dampened on my test ride.Burmashave wrote: Sat Oct 13, 2018 2:00 am I didn't think I'd care about the quick shifter at all, but I've really come to like it. In fact, when I hop back on my Versys 1K, I have to remember to clutch my shifts. On a similar note, I really like the reduced engine brake setting as well.
I find that up and down shifts above 3-4K RPM's seem to go most smoothly, and upshifts in the high RPM range go very smoothly. On all my bikes, I have tended to wind it out in low gear and then short shift up. This works great without the clutch on the H2 provided I'm still accelerating slightly as I'm banging it up from 2-6.
Only allowed low power, and my existing experience is cruiser/upright versys so that's probably a lot of it. But I found it seemed like a lot of effort to lean over on a 60mph curve. The test ride also was less than desirable as it was like 1-2 mins in town before 1 mile on the 60-70mph roadway and then back onto 45mph city streets back to the dealer.
Maybe I'm putting pressure on the bars wrong somehow, or just takes a lot more input. On the v1k I basically can get fairly aggressive leans bouncing off the walls of my lane with just a little twist in my hips and the tiniest action on the handlebars. Just falls right over.
I need to hassle them for another possibly longer ride certainly in higher power mode to get a better feel for it.
0 x
- HouTexH2SX
- Accelerating

- Posts: 235
- Joined: Mon Jul 23, 2018 1:27 pm
- Location: Houston, Texas
- Bike(s): '16 Yamaha FJR1300ES, '18 KTM Super Duke R, '20 Kawasaki Ninja 1000SX
- x 1
Re: Enjoying quick shift
I LOVE the quickshifter on this bike. If you keep the rpm's above 6,000 all upshifts are smooth. I keep the throttle closed for all downshifts and use the clutch for 2 - 1 as I come to a stop.
0 x
- Burmashave
- Supercharged!

- Posts: 542
- Joined: Mon Jul 16, 2018 8:59 pm
- Location: USA
- Bike(s): H2 SX SE
- x 16
- x 11
Re: Enjoying quick shift
My guess is that the difference you felt is due to the fact that the Versys has wider bars, which translates to less steering effort for a bike that weighs about what the SX weighs. I recall that one of the Versys 1K reviewers mentioned that he felt it responded better to steering effort than a Ninja 1K because of the wider bars.Fitz wrote: Sat Oct 13, 2018 2:39 am
How would you compare leaning over on the h2 to the versys 1k? I also have a v1k looking at getting the SX once I get my 2 bikes sold. However some of my enthusiasm was dampened on my test ride.
Personally, I think the SX SE handles much better than my Versys. The handling difference to me is not so much based on effort as confidence. The SX SE feels much, much more confident and planted in corners.
As far as riding in low power mode, you were riding a gelding. The bike is a rush as the supercharger kicks in.
0 x
- THOR
- Accelerating

- Posts: 176
- Joined: Mon Jul 23, 2018 12:31 pm
- Location: London
- Bike(s): Kawasaki H2 SX SE
- x 1
Re: Enjoying quick shift
my quick shifter really works like a dream, from the first to the top very slick.
0 x
Who is online
Users browsing this forum: Bing [Bot], Google [Bot] and 8 guests

