Cornering light always on ?
Cornering light always on ?
hey guys,
is it possible to have Cl on all the time so cars can see you coming better ?
Would it be possible in ecu ? by changing the amount of lean needed
to turn them on ?
Kind regards,
is it possible to have Cl on all the time so cars can see you coming better ?
Would it be possible in ecu ? by changing the amount of lean needed
to turn them on ?
Kind regards,
0 x
- Champ87
- Supercharged!

- Posts: 1289
- Joined: Mon Apr 09, 2018 1:43 am
- Location: NW Indiana US
- Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
- x 304
- x 554
Re: Cornering light always on ?
The settings available on bike only allows you to turn CL on or off. In ECU software there are no options to change the action of cornering lights.
Looking at the wiring diagram it seems that the cornering lights are controlled by CANBUS signal from the ECU. It looks like the left cornering light has some sort of controller so wiring mods to keep them on would not be simple.
So, the simple answer to your question is no. I'm sure it could be done by completely rewiring but no simple answer.
Looking at the wiring diagram it seems that the cornering lights are controlled by CANBUS signal from the ECU. It looks like the left cornering light has some sort of controller so wiring mods to keep them on would not be simple.
So, the simple answer to your question is no. I'm sure it could be done by completely rewiring but no simple answer.
0 x
Champ87
It's amazing how fast you can go when you take your time.
- Pyrocritic
- Boost Engaged

- Posts: 93
- Joined: Wed Dec 20, 2017 5:50 am
- x 4
Re: Cornering light always on ?
champ has it right. trying to get it work via IMU and ECU hacking seems like massively complicated and too much trouble.
An easier solution is to probably just do an electrical hack. Find power and ground for all 3 LED on, snip everything else, wire them to voltage that's link to ignition, and maybe run it through a switch/fuse.
the problem with this is you will probably have the CL error on your TFT the entire time. Next time you have one unplugged turn on your ignition. The ECU throws an error.
Anyway seems like a massive pain in the arse either way.
An easier solution is to probably just do an electrical hack. Find power and ground for all 3 LED on, snip everything else, wire them to voltage that's link to ignition, and maybe run it through a switch/fuse.
the problem with this is you will probably have the CL error on your TFT the entire time. Next time you have one unplugged turn on your ignition. The ECU throws an error.
Anyway seems like a massive pain in the arse either way.
0 x
- THOR
- Accelerating

- Posts: 176
- Joined: Mon Jul 23, 2018 12:31 pm
- Location: London
- Bike(s): Kawasaki H2 SX SE
- x 1
Re: Cornering light always on ?
no this is not possible as they are working with the tilt sensor. in Ktm it's not possible as well. If you wire to a button to these lights the bike Bus wire doesn't accept it. you won't be able to.
0 x
- Pyrocritic
- Boost Engaged

- Posts: 93
- Joined: Wed Dec 20, 2017 5:50 am
- x 4
Re: Cornering light always on ?
I guarantee you it can be done, its just not as simple as old school bikes.THOR wrote: Sat Aug 11, 2018 7:15 am no this is not possible as they are working with the tilt sensor. in Ktm it's not possible as well. If you wire to a button to these lights the bike Bus wire doesn't accept it. you won't be able to.
you can ride the bike perfectly fine with the ECU/CAN not detecting the cornering light harness even plugged in, it just shows a CL error on the dash. At the end of the day we're talking about a set of LEDs that need voltage, that's all. You just isolate the cornering light LEDs (and switch if one is used) entirely from the ECU/CAN loop.
this is not alien technology.
maybe you can disable the CL error on the dash by jumping the end of the CL connector on the bike side with a resistor or something.
anyway it can be done, I just don't think its worth the hassle.
0 x
- HouTexH2SX
- Accelerating

- Posts: 235
- Joined: Mon Jul 23, 2018 1:27 pm
- Location: Houston, Texas
- Bike(s): '16 Yamaha FJR1300ES, '18 KTM Super Duke R, '20 Kawasaki Ninja 1000SX
- x 1
Re: Cornering light always on ?
I was surprised that they work during the day. The ones on my '16 FJR1300 only work at night (same set up with 3 progressive lights on each side of the headlight cluster).
0 x
- KajKokkola
- New Member

- Posts: 1
- Joined: Wed Aug 04, 2021 4:04 pm
- Location: Finland
- Bike(s): H2 sx se
Re: Cornering light always on ?
Hello , I can t get the cornering lights on.Fuse is ok.But not working.Help? H12 SX SE 2019
0 x
- Champ87
- Supercharged!

- Posts: 1289
- Joined: Mon Apr 09, 2018 1:43 am
- Location: NW Indiana US
- Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
- x 304
- x 554
Re: Cornering light always on ?
Obvious question: did you turn them on in the menu?KajKokkola wrote: Wed Aug 04, 2021 4:20 pm Hello , I can t get the cornering lights on.Fuse is ok.But not working.Help? H12 SX SE 2019
If they're On then try the following check procedure to see if you can identify the problem:
1 x
Champ87
It's amazing how fast you can go when you take your time.
- prettybirdSE
- Supercharged!

- Posts: 1149
- Joined: Sat Aug 15, 2020 7:30 pm
- Location: Montana
- Bike(s): 2020 Ninja H2SXSE+
- x 537
- x 145
Re: Cornering light always on ?
"Hello , I can t get the cornering lights on.Fuse is ok.But not working.Help? H12 SX SE 2019"
Turn bike on and start.Using right mode button,press to enter 'vehicle settings'
Press mode button to settings list.Scroll down with left switchgear button to 'cornering lights'.Press right mode button.Press left up or down button to highlight 'on' or 'off'.When selected('on') press reset button.(do not hold).Press again to leave settings display menu.You should be at the normal rider mode display again(if you've selected Rider mode in the menu).
BIKE MUST BE RUNNING.
There's nothing wrong with your electricals or fuses or anything.
Turn bike on and start.Using right mode button,press to enter 'vehicle settings'
Press mode button to settings list.Scroll down with left switchgear button to 'cornering lights'.Press right mode button.Press left up or down button to highlight 'on' or 'off'.When selected('on') press reset button.(do not hold).Press again to leave settings display menu.You should be at the normal rider mode display again(if you've selected Rider mode in the menu).
BIKE MUST BE RUNNING.
There's nothing wrong with your electricals or fuses or anything.
Last edited by prettybirdSE on Wed Aug 04, 2021 5:43 pm, edited 1 time in total.
0 x
- unknownbiker
- Chirp-Chirp!

- Posts: 352
- Joined: Thu Apr 02, 2020 10:21 pm
- Location: Canada East
- Bike(s): H2 SX
- x 557
- x 93
Re: Cornering light always on ?
Might be a way to keep them always on but you will loose your cornering angle readout. If you took the tilt sensor & tipped it while the bike was running to see how far it has to go to make each side light up, then you could find out the resistance of the wires coming out vs straight up & down, & wire a same rated resistor in there to by pass it, making the ECU think you were always leaning... both ways
Thered be more to it than that, but It would be interesting to try... 
0 x
Jesus Saves.
Who is online
Users browsing this forum: No registered users and 10 guests
