Self-Tuning Thread

Bike aesthetic/mechanical/electrical modifications and general wrenching advice.
User avatar
Kawil0vr1988
New Member

New Member
Posts: 11
Joined: Mon Aug 06, 2018 4:52 pm
Bike(s): H2 Sx

Re: Self-Tuning Thread

Post by Kawil0vr1988 » Sat Sep 08, 2018 10:02 pm


:cool:
Last edited by Kawil0vr1988 on Sat Sep 15, 2018 5:52 pm, edited 3 times in total.
0 x

User avatar
THOR
Accelerating

Accelerating
Posts: 176
Joined: Mon Jul 23, 2018 12:31 pm
Location: London
Bike(s): Kawasaki H2 SX SE
x 1

Re: Self-Tuning Thread

Post by THOR » Sat Sep 08, 2018 10:07 pm


the bike is not slow its heavy that's why it feels slow.
Last edited by THOR on Mon Sep 17, 2018 9:09 pm, edited 1 time in total.
0 x

User avatar
Kawil0vr1988
New Member

New Member
Posts: 11
Joined: Mon Aug 06, 2018 4:52 pm
Bike(s): H2 Sx

Re: Self-Tuning Thread

Post by Kawil0vr1988 » Sat Sep 08, 2018 10:10 pm


Yeah maybe that’s what it is. My friend has a brand new s1k he had me by about 3 bike lengths before so I guess we shall see next time I see Him
Last edited by Kawil0vr1988 on Sat Sep 15, 2018 5:53 pm, edited 1 time in total.
0 x

User avatar
THOR
Accelerating

Accelerating
Posts: 176
Joined: Mon Jul 23, 2018 12:31 pm
Location: London
Bike(s): Kawasaki H2 SX SE
x 1

Re: Self-Tuning Thread

Post by THOR » Sat Sep 08, 2018 10:24 pm


just best to make the bike lighter the you will like it more , get rid of things you dont need, like mid stand and cat.
Last edited by THOR on Mon Sep 17, 2018 9:09 pm, edited 1 time in total.
0 x

User avatar
Snakes709
Supercharged!

Supercharged!
Posts: 1399
Joined: Sun Aug 19, 2018 2:42 am
Location: Edmonton, AB
Bike(s): 2018 H2 SX SE
x 11
x 394

Re: Self-Tuning Thread

Post by Snakes709 » Sat Sep 08, 2018 10:52 pm


cat, centre stand, lithium battery, passenger pegs, cf rims(expensive but worth it) That's a good chunk of weight right there. Stock SE is what, like 570lbs? those mods right there will bring it close to 500. Plus the cf rims is rotational mass.
0 x

2018 H2 SX/SE
-ZX10R Headers
-2016+ ZX10R Yoshimura Alpha 3/4 system
-Sprint P08 Filter
-Vcyclenut flash
-Driven block off plates
-Yager Werx Intercooler

User avatar
Kawil0vr1988
New Member

New Member
Posts: 11
Joined: Mon Aug 06, 2018 4:52 pm
Bike(s): H2 Sx

Re: Self-Tuning Thread

Post by Kawil0vr1988 » Sat Sep 08, 2018 11:21 pm


Yeah I guess bst wheels are next
Last edited by Kawil0vr1988 on Sat Sep 15, 2018 5:54 pm, edited 2 times in total.
0 x

User avatar
Snakes709
Supercharged!

Supercharged!
Posts: 1399
Joined: Sun Aug 19, 2018 2:42 am
Location: Edmonton, AB
Bike(s): 2018 H2 SX SE
x 11
x 394

Re: Self-Tuning Thread

Post by Snakes709 » Sun Sep 09, 2018 12:32 am


I would leave the boost alone. There is so much more power in these bikes without needing more boost. Weight reduction and gearing is your best bet. That being said, you gotta remember the S1000RR is a super sport, we are on sport touring.
Last edited by Snakes709 on Tue Sep 11, 2018 2:47 pm, edited 1 time in total.
0 x

2018 H2 SX/SE
-ZX10R Headers
-2016+ ZX10R Yoshimura Alpha 3/4 system
-Sprint P08 Filter
-Vcyclenut flash
-Driven block off plates
-Yager Werx Intercooler

User avatar
vcyclenut
Supercharged!

Supercharged!
Posts: 1004
Joined: Mon Jan 22, 2018 4:44 pm
Location: Blaine, WA
x 28
x 60

Re: Self-Tuning Thread

Post by vcyclenut » Mon Sep 10, 2018 3:08 pm


Kawil0vr1988 wrote: Sat Sep 08, 2018 10:02 pm 2BCD9BE7-6D0E-4F1A-A3DD-D16B8874ADA0.jpeg
I just got my bike back from the dyno has air filter, catless and m4 slip on. Bike still feels kind of slow to me. here’s the before and after dyno graph this is also stock rev limiter as well

very nice gains!!

did he give you a graph with the air fuel??
0 x

User avatar
Snakes709
Supercharged!

Supercharged!
Posts: 1399
Joined: Sun Aug 19, 2018 2:42 am
Location: Edmonton, AB
Bike(s): 2018 H2 SX SE
x 11
x 394

Re: Self-Tuning Thread

Post by Snakes709 » Wed Nov 14, 2018 8:13 pm


kman0066 wrote: Fri Jul 20, 2018 7:34 pm Since I decided to go with the ZX-10R titanium header and slip-on, I decided to go down the tune it myself route. I'll preface this whole discussion with, if you have a stock-header bike, I'd just go with Vcyclenut's flash in a heartbeat (it saves you all sorts of money and time, and it's a proven result). That said, I got the Woolich setup with autotune/logbox for mine to get the day-to-day driving tune done along with a baseline setup to get it on the dyno for a local tuner. Starting a thread to share my results and findings here. I've had it for just a few days so far, so just getting into it.

My bike:
Kawasaki H2 SX SE
2011 ZX-10R titanium header installed with custom made spacers
Graves Carbon Fiber/Titanium slip-on for 11 ZX-10R (eliminates center stand)
Sprint F1-85 air filter (purchased from VCyclenut)
PAIR Valves blocked off


I installed the Woolich harness no problem. Getting to the ECU is kind of a pain on this bike, but doable in about an hour total. All that time is getting fairings out of the way. Installing the logbox and wideband O2 sensor for me was easy because the Graves slip-on I used came with a wideband O2 port installed on it. If you were using the stock header, you'd have to use an adapter (less ideal) or get a bigger port welded in. I also spent some timing removing the exhaust valve and cables since I no longer have the valve itself. That's kind of a pain to get to the back bolt. If I had to do that again, I'd take the passenger seat mounting bracket off before trying to remove the bolt.

From there, I did the basics on the ECU: Disabled error codes for blocking off Pair valves, disabled stock o2 sensor, disabled fuel cut on decel, disabled exhaust valve, and removed speed limiter.

From other's findings, I did raise the rev limiter 500 RPMs to a new redline of 13k RPMs. It definitely pulls to that no problem. Stopping there as hitting 13k RPMs at the rate of acceleration it does, causes it to over-rev to ~13.5k just from momentum as evidenced in the data logs for me.

Throttle plates: WOW, people aren't kidding. The throttle plates barely open in a lot of cases on the throttle maps. I changed the throttle settings to go open 100% at 100% throttle. I started letting it go 100% at 7000rpm and up. This made it kick in the power kind of harsh at 7000, so I went back in and opened it up fully at 6000 and feathered it down below that to make a smoother transition.

For timing: I started off with 2 degrees advance after 7k rpms. That produced a noticeable power gain. So I added 2 more degrees (for a total of 4 degrees advance from stock), and that produced even more power. So for now, I'm leaving it there until I get the dyno time to test it out scientifically. I doubt an across the board advance will be the way to go. You can really feel the effect of the timing changes as I didn't make them across the board and I can feel exactly when it kicks in.

Fueling: Interesting results here. Running the stock map, with my timing changes and throttle map changes, I'm actually pretty close to ideal all the way until 9500 rpms. Just slightly rich, but within acceptable limits. Below 9500, I don't have anything above 5% change, and mostly below 3% except for 1 cell. Above 9500 RPMs, I was getting ~10:1 readings on the wide-band, pretty rich. I've since corrected to pull roughly 10-15% fuel up top at the suggestion of autotune, and that's where I'm at for my next test, but the weather is crappy so have to wait to test.

Once I get some time on a dyno over the next couple months, I'll be submitting my map to the Woolich map-share for people who decide to go the ZX-10R header route. I'm not a professional tuner, so no promises, warranty, etc. offered. I doubt the tune would be good for a stock bike and I doubt it would be good for a different header design. Just trying to add to the community. My aspirations are to reach 230 WHP, and I won't be trying to go past that, if I can even reach it. Not sure how feasible that is, but I'm happy with the feel so far. It pulls ridiculous already and it's not even barely been tuned.

I am getting a little concerned over boost temps. I saw it climb to the 170s after just a little fun, so I'm going to be as cautious about timing as I can be until I get some good data there. Not having an inter-cooler and running the high-compression pistons like our bike has, it's a recipe for pre-detonation if the temps get high. Not sure what that temp is, but I hope to not find it :)
What wire did you tap into for power? Installing my woolich system now. Used the positive wire for the brake light in my 10r and 14r. Just wondering if you didnthe same.
0 x

2018 H2 SX/SE
-ZX10R Headers
-2016+ ZX10R Yoshimura Alpha 3/4 system
-Sprint P08 Filter
-Vcyclenut flash
-Driven block off plates
-Yager Werx Intercooler

User avatar
kman0066
Accelerating

Accelerating
Posts: 223
Joined: Wed Dec 06, 2017 3:34 pm
Location: Nolensville, TN
x 1

Re: Self-Tuning Thread

Post by kman0066 » Fri Nov 16, 2018 2:46 am


If the instructions don't specify (can't remember), I would tend to go for the tail light wire for a switched power source.
0 x

Post Reply

Who is online

Users browsing this forum: Bing [Bot] and 14 guests