I attempted to set sag on my bike. The rear spring seems to be plenty strong enough, but I cannot get the sag setting right. With only me (I am 200lbs in gear) and the preload adjuster at maximum, I am still 5-6mm short of sag. I started this comment in a tire pressure thread, but decided to start a new one.
Well, the issue is more complicated than I anticipated. The stock shock adjuster has 10mm travel, which is more than I expected. If I bump this up another 5-6mm, I don't know that I will be happy with the riding position (tail up). This is not a track beast. The bike has plenty of turn in. I looked at modifying the shock mount to raise it up, but I cannot imagine that I can get anything more than 5mm up. That would help, but I would still be at maximum on my adjuster.
I am going make my own shock mount soon to get the additional ~5mm drop that I see is possible and run a 10mm longer spring. It may be enough for me. I am heading out now to a suspension shop today to measure the length and pressure of the stock spring. I will update when I am finished.
I am heading to Las Vegas on my bike on Friday (approximately 500 miles each way). I really wanted this resolved before I left. My KQR bags will be fully loaded so I expect to be at the bottom of my shock for the trip. Ugh.
Stock spring length
- Champ87
- Supercharged!

- Posts: 1289
- Joined: Mon Apr 09, 2018 1:43 am
- Location: NW Indiana US
- Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
- x 304
- x 554
Re: Stock spring length
I'm having trouble understanding the situation. It's clear to you because you played with the settings but I'm having trouble picturing it from your description.
You should be able to get correct sag and ride height without modifying shock mounts. At worst it might require a different rate spring but hard to image a 200 lb rider is pushing beyond the standard design parameters.
You say you are 5-6mm short of sag. Do you mean you don't have enough sag - bike sit's too high. If it's sitting too high why do you have preload wound to the max?57x wrote: Wed May 16, 2018 9:16 pmWith only me (I am 200lbs in gear) and the preload adjuster at maximum, I am still 5-6mm short of sag.
Or do you mean it sits 5-6mm below the recommended sag? If it sits too low you wouldn't be concerned about a tail up riding position. Besides, setting 20-30mm sag isn't going to put the tail up in the air.57x wrote: Wed May 16, 2018 9:16 pmIf I bump this up another 5-6mm, I don't know that I will be happy with the riding position (tail up).
You should be able to get correct sag and ride height without modifying shock mounts. At worst it might require a different rate spring but hard to image a 200 lb rider is pushing beyond the standard design parameters.
0 x
Champ87
It's amazing how fast you can go when you take your time.
- 57x
- Accelerating

- Posts: 202
- Joined: Thu Apr 19, 2018 2:45 am
- Location: California, USA
- Bike(s): 2018 H2 SX SE
- x 2
Re: Stock spring length
I am 16mm short (too low) for the sag numbers with the low setting on the preload adjuster. There is 10mm adjustment up, which I am using to compensate. I have come to the conclusion, and talking to several suspension tuners that I just don't have a strong enough spring. Typical Japanese bikes made for a 50kg/110lb rider. It is not a spring height issue. I will start with .5kg more that stock on my first try, once I test the stock spring pressure to see what it is.
I really don't want to jack the ass end of this thing up, but that appears what is necessary to get sag correct. I am already up 10mm, so another 5-6mm probably won't be too much of a problem.
I really don't want to jack the ass end of this thing up, but that appears what is necessary to get sag correct. I am already up 10mm, so another 5-6mm probably won't be too much of a problem.
0 x
- Champ87
- Supercharged!

- Posts: 1289
- Joined: Mon Apr 09, 2018 1:43 am
- Location: NW Indiana US
- Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
- x 304
- x 554
Re: Stock spring length
So what about the front? If the suspension really was designed around a 50 kg rider then you'll have a similar problem with front sag. You'll need to increase the front spring rate too and so the bike will remain level.
Japanese bikes made for a 50kg rider? Maybe in the 1970s - not so these days. Suspension drew praise in pretty much all the test reports but if you're not happy with it then it matters not what the reviewers thought.
Japanese bikes made for a 50kg rider? Maybe in the 1970s - not so these days. Suspension drew praise in pretty much all the test reports but if you're not happy with it then it matters not what the reviewers thought.
0 x
Champ87
It's amazing how fast you can go when you take your time.
- 57x
- Accelerating

- Posts: 202
- Joined: Thu Apr 19, 2018 2:45 am
- Location: California, USA
- Bike(s): 2018 H2 SX SE
- x 2
Re: Stock spring length
The front is fine. The spring is ok if I rode on my own, never carrying bags. I want my sag right with no preload so I can carry my bags, etc., like I am next week. 1000 mile ride in the High Desert of California and Nevada (500 miles each way). I hope my tires hold up. I already have 1600 miles on them. The tires look great now with tons of tread left, but several people did not get this many miles in the first place. There is hardly a straight road for the whole 500 miles.
0 x
- 57x
- Accelerating

- Posts: 202
- Joined: Thu Apr 19, 2018 2:45 am
- Location: California, USA
- Bike(s): 2018 H2 SX SE
- x 2
Re: Stock spring length
Have you ever done something that you feel really dumb about?
I was under a bad assumption that the H2 SX has the common 90mm rear wheel travel on most modern bikes. Normal settings for sag are ~1/3 of rear wheel travel. I just looked up that the H2 SX has 139mm of rear wheel travel. My sag setting is coming in at around 45.5mm. I was expecting around 30mm sag.
90mm / 3 = 30mm
146mm / 3= 46.3mm
I am actually around .8 mm too much spring for me on the bike. Damn. I guess it is just time to put the shock back on and ride. I am so glad I caught this before swapping the spring.
Feeling rather silly .............

I was under a bad assumption that the H2 SX has the common 90mm rear wheel travel on most modern bikes. Normal settings for sag are ~1/3 of rear wheel travel. I just looked up that the H2 SX has 139mm of rear wheel travel. My sag setting is coming in at around 45.5mm. I was expecting around 30mm sag.
90mm / 3 = 30mm
146mm / 3= 46.3mm
I am actually around .8 mm too much spring for me on the bike. Damn. I guess it is just time to put the shock back on and ride. I am so glad I caught this before swapping the spring.
Feeling rather silly .............
0 x
Who is online
Users browsing this forum: No registered users and 11 guests
