Murph's bar riser design update #3

Post by **murph** » Sat Jun 27, 2020 4:50 pm

Greetings folks,

Murph here of Murphskits, I read through the rules and didn't see where it was prohibited for a merchant to post on his own product, if i'm in violation let me know. I have made it a point not to be a forum member just to peddle our own goods, Im just dropping in here to see how the proto types are working out. We are going to trim the area above the clutch safety switch for more clearance. What interference we have with the controls contacting the screen on the left side...we have done all we can ..if you would please send your feedback and suggestions to murph@murphskits.com.. I would apricate it . I'm spread pretty thin so not looking at forums keeps me on task Also wanted to give public acknowledgement to Neal Ulen for his help early on with the project..Neal when we have the finished units yours will be on the way!
Best

Murph

Post by **SDH2Mike** » Sat Jun 27, 2020 10:09 pm

Murph there is a vendor forum, I think you can post up your risers when you have the mounts finalized for the members to check out. Glad you stuck with the project. Options are always good.

Post by **TurboBob** » Sat Jun 27, 2020 10:40 pm

Murph, I sent you a private message.

Post by **UFO** » Sun Jul 05, 2020 4:44 pm

murph wrote: Sat Jun 27, 2020 4:50 pm Greetings folks,

Murph here of Murphskits, I read through the rules and didn't see where it was prohibited for a merchant to post on his own product, if i'm in violation let me know. I have made it a point not to be a forum member just to peddle our own goods, Im just dropping in here to see how the proto types are working out. We are going to trim the area above the clutch safety switch for more clearance. What interference we have with the controls contacting the screen on the left side...we have done all we can ..if you would please send your feedback and suggestions to murph@murphskits.com.. I would apricate it . I'm spread pretty thin so not looking at forums keeps me on task Also wanted to give public acknowledgement to Neal Ulen for his help early on with the project..Neal when we have the finished units yours will be on the way!
Best

Murph

Murph, I'm so glad these are being finished up! When I passed it on to you I just didn't have time to devote to it anymore with my health problems last year. I'm surprised I lasted as long as I did sitting in front of my computer doing CAD at the time.

Look forward to seeing the final version.

Also, feel free to post a link to the final product page in the Vendor forum. That's why it's there.

Post by **UFO** » Wed Sep 09, 2020 12:56 am

Is there an update from those who received parts 2-3 months ago? Were they good? Are these in production yet?

Post by **Prof J** » Wed Sep 09, 2020 3:24 am

UFO wrote: Wed Sep 09, 2020 12:56 am Is there an update from those who received parts 2-3 months ago? Were they good? Are these in production yet?

UFO, I received a few sets. I posted up some info here:
viewtopic.php?f=8&t=1820&p=17731&hilit=Murph#p17731

I think there were some slight? changes to this initial setup. I thought Murph put that info up here. (?)

I'm about to take a setup to a tig welder this or next week to mod and raise it as the above post references.

I just heard back from Murph today that they do not have the setup to do a higher riser as I wished, and 'stacked' in the post. So I hope to do it myself, as the Little Red Hen says... old children's' story.

Post by **SidneyCarton** » Fri Sep 18, 2020 3:37 am

Final version installed.

Post by **esenior** » Thu Jan 21, 2021 8:52 pm

Any update on availability? I'm at the point where the 1/2 riser isn't enough and am contemplating the ABM bars, but really don't want to have to get rid of my Ohlins damper. Are the Murphs risers going to be available any time soon?

Post by **FJR919** » Fri Jan 22, 2021 12:44 am

I don't want to speak for Murph but news should be very soon. I just did an installation video for him. Stay tuned...

Post by **murph** » Sat Jan 23, 2021 10:40 pm

Hey gang

sorry for the long disappearance.. been a very busy year. We have our risers ready to go! I would like to thank this forum for the amount of help several members have provided , it simply would not have happened with out you.

https://murphskits.com/h2/

All the details are there, and a link to an installation video graciously done by a forum member .

I don't lurk on forums to push sales, if you have questions please drop me an email : murph@murphskits.com

We also added paypals payment plan

just in case

Thanks to you all again! you know who you are..

Id like to develop our "bearing up" shifter mod for this bike as well...its under $30!

All the best,,

Murph

Murph's bar riser design update #3

Re: Murph's bar riser design update #3

Re: Murph's bar riser design update #3

Re: Murph's bar riser design update #3

Re: Murph's bar riser design update #3

Re: Murph's bar riser design update #3

Re: Murph's bar riser design update #3

Re: Murph's bar riser design update #3

Re: Murph's bar riser design update #3

Re: Murph's bar riser design update #3

Re: Murph's bar riser design update #3

Who is online