Full System (02 sensor/servo removal)

Bike aesthetic/mechanical/electrical modifications and general wrenching advice.
Post Reply
User avatar
KompreSXor
Accelerating

Accelerating
Posts: 192
Joined: Sun Sep 23, 2018 10:17 am
Location: UK
Bike(s): 2018 H2SXSE
x 3
x 77

Full System (02 sensor/servo removal)

Post by KompreSXor » Sun Jun 09, 2019 8:26 am


I’m currently running just a slip-on and a sprint filter. I plan to install 10r headers and 3/4 system, and I can’t find any firm answers about what to do with the electrical side of the modification. Does anyone know:

1. Can I remove the exhaust servo without triggering error codes?
2. Can I remove the 02 sensor without triggering error codes? Or is it required for tuning/dyno?
3. Can I ride my bike to the dyno/tuner after the install, or will it be harmful to the engine?
4. Can ECU remapping ‘map out’ the servo and 02 sensor and reset errors if required?

I’m interested in what the guys with full systems have done, as information is a bit scarce.. cheers!
0 x

2018 H2 SX SE
-ZX10R Ti Headers/Arrow system
-Sprint P08
-PROJEX Flash 224 rwhp 110ft/lb
-KLEEN Block Off Plates
-Ninja H2 330mm Brembo Rotors
-Brembo M4
-Ohlins TTX36
-Ninja H2 Swing Arm
-23kg Weight Reduction
-187.15mph Elvington airfield

User avatar
PhukDD
Accelerating

Accelerating
Posts: 201
Joined: Fri Apr 19, 2019 3:24 pm
Location: Around Phoenix
Bike(s): a green one

Re: Full System (02 sensor/servo removal)

Post by PhukDD » Sun Jun 09, 2019 12:23 pm


I just did a deCat mod. We removed everything you are referring to. When we put everything back together the bike was all pissy about its missing friends(O2 and Servo) . I had MTC put a wide band O2 bung in the mid pipe to install the Woolich kit. We simply cleared the codes with the software. You can do the same with one of those code reader units. The flash disabled these things but the bike was still looking for them. It is fine now. I am not smart enough to answer your question about riding to the tuner....sorry.
0 x

User avatar
Champ87
Supercharged!

Supercharged!
Posts: 1289
Joined: Mon Apr 09, 2018 1:43 am
Location: NW Indiana US
Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
x 304
x 554

Re: Full System (02 sensor/servo removal)

Post by Champ87 » Sun Jun 09, 2019 3:00 pm


KompreSXor wrote: Sun Jun 09, 2019 8:26 am1. Can I remove the exhaust servo without triggering error codes?
2. Can I remove the 02 sensor without triggering error codes? Or is it required for tuning/dyno?
No, you will trigger error codes 33 and 34 if the sensors are not disabled in the ECU.

Stock O2 sensor is not needed for tuning. Your tuner may want to use a wideband O2 sensor. In that case you would need the correct size bung in the exhaust system as PhukDD mentioned.

A few years back I had my Triumph Sprint tuned. The tuner used a 5 gas analyser inserted into the end of exhaust so I didn't need to worry about the wideband sensor. Best to ask your tuner.
KompreSXor wrote: Sun Jun 09, 2019 8:26 am3. Can I ride my bike to the dyno/tuner after the install, or will it be harmful to the engine?
Should be OK. Obviously, don't whip it on the way no matter how tempting it is. Also, don't lug along with high load/low rpm. Keep in mind, you'll have the engine warning light showing due to O2 sensor and butterfly valve removal so it might feel like a ride to Doomsville.
KompreSXor wrote: Sun Jun 09, 2019 8:26 am4. Can ECU remapping ‘map out’ the servo and 02 sensor and reset errors if required?
Yes. Woolich software, for example, has options to "Disable O2 Sensor FI code" and "Disable Exhaust Valve Servo Motor".

The other thing to consider is the secondary air system. You may see it referred to as PAIR but I think that may be Suzuki's name for it. It doesn't affect power but it can mess up Air/Fuel readings for the tuner. Ask you tuner about that.

Most riders will disable the secondary air system when their bike is tuned. The bike will run fine with it in place but disabling it will reduce exhaust heat. Also, certain tunes create popping and banging in the exhaust on overrun if the secondary air system is left in place. To disable it you need to install block off plates and the tune should disable it in the ECU too.
0 x

Champ87
It's amazing how fast you can go when you take your time.

User avatar
KompreSXor
Accelerating

Accelerating
Posts: 192
Joined: Sun Sep 23, 2018 10:17 am
Location: UK
Bike(s): 2018 H2SXSE
x 3
x 77

Re: Full System (02 sensor/servo removal)

Post by KompreSXor » Sun Jun 09, 2019 5:26 pm


Thanks guys, your answers have helped a lot.. I might make it a winter project, and trailer it to the tuners..
0 x

2018 H2 SX SE
-ZX10R Ti Headers/Arrow system
-Sprint P08
-PROJEX Flash 224 rwhp 110ft/lb
-KLEEN Block Off Plates
-Ninja H2 330mm Brembo Rotors
-Brembo M4
-Ohlins TTX36
-Ninja H2 Swing Arm
-23kg Weight Reduction
-187.15mph Elvington airfield

User avatar
Racer-X
Supercharged!

Supercharged!
Posts: 254
Joined: Sun Apr 07, 2019 10:10 pm
x 4
x 44

Re: Full System (02 sensor/servo removal)

Post by Racer-X » Sun Jun 09, 2019 9:54 pm


Why would you want to remove the butterfly/servo? Doesn't that help the bike have better low/mid range power?
0 x

User avatar
PhukDD
Accelerating

Accelerating
Posts: 201
Joined: Fri Apr 19, 2019 3:24 pm
Location: Around Phoenix
Bike(s): a green one

Re: Full System (02 sensor/servo removal)

Post by PhukDD » Sun Jun 09, 2019 10:58 pm


Racer-X wrote: Sun Jun 09, 2019 9:54 pm Why would you want to remove the butterfly/servo? Doesn't that help the bike have better low/mid range power?
Because the valve is off, that servo has to weigh 5lbs.
0 x

User avatar
PhukDD
Accelerating

Accelerating
Posts: 201
Joined: Fri Apr 19, 2019 3:24 pm
Location: Around Phoenix
Bike(s): a green one

Re: Full System (02 sensor/servo removal)

Post by PhukDD » Sun Jun 09, 2019 11:00 pm


On the topic of block off plates..I just disabled the valve with the flash...I am not sure the plates are required.
0 x

User avatar
Champ87
Supercharged!

Supercharged!
Posts: 1289
Joined: Mon Apr 09, 2018 1:43 am
Location: NW Indiana US
Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
x 304
x 554

Re: Full System (02 sensor/servo removal)

Post by Champ87 » Mon Jun 10, 2019 1:12 am


PhukDD wrote: Sun Jun 09, 2019 11:00 pmOn the topic of block off plates..I just disabled the valve with the flash...I am not sure the plates are required.
My understanding - disabling in the ECU only prevents Check Engine LIght/Error Code. Even if that's not correct, I don't see much point leaving it there if it's disabled.
0 x

Champ87
It's amazing how fast you can go when you take your time.

Post Reply

Who is online

Users browsing this forum: Bing [Bot] and 15 guests