Bike aesthetic/mechanical/electrical modifications and general wrenching advice.
-
Bryan468
- Supercharged!

- Posts: 433
- Joined: Tue Apr 02, 2019 7:52 pm
- x 35
- x 86
Post
by Bryan468 » Mon Jun 03, 2019 11:29 pm
Burmashave wrote: Mon Jun 03, 2019 5:02 pm
Question for folks who have flushed their clutch reservoir:
How did you fill that tiny reservoir without dribbling any around it? I ask because my hands aren't very steady. I don't mind flushing and bleeding brakes, but trying not to dribble any brake fluid makes me mental, which only makes things worse.
I usually just pour it right from the bottle to the reservoir.
I would recommend you put the bike on the center stand, turn the bars so the reservoir is at the easiest place to get the bottle in there to pour, put some shop towels all around the reservoir so when you spill or drip you’re covered, and have another towel ready to go so you can immediately wipe up anything that spills.
0 x
-
JonTheChron
- Supercharged!

- Posts: 539
- Joined: Sun Dec 10, 2017 9:00 pm
- Location: Quebec
- Bike(s): H2 SX SE '18
- x 7
- x 6
Post
by JonTheChron » Wed Jun 05, 2019 2:00 pm
I poured directly from the bottle to the reservoir, I guess you could use a clean syringe from the drug store
0 x
2018 H2 SX SE (1st in Canada)
2011 Ninja 1000 (sold)
2009 Ninja 250R (sold)
-
KompreSXor
- Accelerating

- Posts: 192
- Joined: Sun Sep 23, 2018 10:17 am
- Location: UK
- Bike(s): 2018 H2SXSE
- x 3
- x 77
Post
by KompreSXor » Wed Jun 05, 2019 2:11 pm
Burmashave wrote: Mon Jun 03, 2019 5:02 pm
Question for folks who have flushed their clutch reservoir:
How did you fill that tiny reservoir without dribbling any around it? I ask because my hands aren't very steady. I don't mind flushing and bleeding brakes, but trying not to dribble any brake fluid makes me mental, which only makes things worse.
I put a square of kitchen roll/ poly roll over the reservoir with a small enough hole in it to fit over to catch any drips, and I use a 100ml plastic syringe I bought from eBay. I use it on all my fluid changes. No mess, no fuss.
0 x
2018 H2 SX SE
-ZX10R Ti Headers/Arrow system
-Sprint P08
-PROJEX Flash 224 rwhp 110ft/lb
-KLEEN Block Off Plates
-Ninja H2 330mm Brembo Rotors
-Brembo M4
-Ohlins TTX36
-Ninja H2 Swing Arm
-23kg Weight Reduction
-187.15mph Elvington airfield
-
Burmashave
- Supercharged!

- Posts: 542
- Joined: Mon Jul 16, 2018 8:59 pm
- Location: USA
- Bike(s): H2 SX SE
- x 16
- x 11
Post
by Burmashave » Wed Jun 05, 2019 6:55 pm
KompreSXor wrote: Wed Jun 05, 2019 2:11 pm
Burmashave wrote: Mon Jun 03, 2019 5:02 pm
Question for folks who have flushed their clutch reservoir:
How did you fill that tiny reservoir without dribbling any around it? I ask because my hands aren't very steady. I don't mind flushing and bleeding brakes, but trying not to dribble any brake fluid makes me mental, which only makes things worse.
I put a square of kitchen roll/ poly roll over the reservoir with a small enough hole in it to fit over to catch any drips, and I use a 100ml plastic syringe I bought from eBay. I use it on all my fluid changes. No mess, no fuss.
That sounds a plan. Thanks.
0 x
Who is online
Users browsing this forum: Bing [Bot] and 9 guests