Ecu modification
-
Drnick
- Chirp-Chirp!
- Posts: 349
- Joined: Mon Apr 23, 2018 1:52 am
- Location: Pompano beach,Florida
- Bike(s): Too many to list!
- x 3
Ecu modification
Is there a link to do this one wire mod so I can easily reflash without removing ECU.
0 x
Velocitus Eradicus
-
Snakes709
- Supercharged!
- Posts: 1396
- Joined: Sun Aug 19, 2018 2:42 am
- Location: Edmonton, AB
- Bike(s): 2018 H2 SX SE
- x 11
- x 387
Re: Ecu modification
What wire mod? Are you talkig about the ecu harness from woolich?
0 x
2018 H2 SX/SE
-ZX10R Headers
-2016+ ZX10R Yoshimura Alpha 3/4 system
-Sprint P08 Filter
-Vcyclenut flash
-Driven block off plates
-Yager Werx Intercooler
-
JonTheChron
- Supercharged!
- Posts: 539
- Joined: Sun Dec 10, 2017 9:00 pm
- Location: Quebec
- Bike(s): H2 SX SE '18
- x 7
- x 6
Re: Ecu modification
Correct me of I'm wrong, but I believe you have to reach the ECU to install the on-bike reflash harness from WoolishDrnick wrote: Thu Apr 18, 2019 4:44 pm Is there a link to do this one wire mod so I can easily reflash without removing ECU.
0 x
2018 H2 SX SE (1st in Canada)
2011 Ninja 1000 (sold)
2009 Ninja 250R (sold)
-
Drnick
- Chirp-Chirp!
- Posts: 349
- Joined: Mon Apr 23, 2018 1:52 am
- Location: Pompano beach,Florida
- Bike(s): Too many to list!
- x 3
Re: Ecu modification
No my tuner says one wire that has to be installed in a certain pin # on harness on connector on Ecu,then u route wire to back of bike for easy access. I just don’t know all the specifics
On this mod.
On this mod.
0 x
Velocitus Eradicus
-
Snakes709
- Supercharged!
- Posts: 1396
- Joined: Sun Aug 19, 2018 2:42 am
- Location: Edmonton, AB
- Bike(s): 2018 H2 SX SE
- x 11
- x 387
Re: Ecu modification
Yea its the same thing. Ecu doesnt have to come out, you just need access to the connectors. Disconnect the connectors, pop the white pin cover out, put your new wire in, make sure its in the correct way and seated fully and just route it back to where you have your log box. Here is my setup
- Attachments
-
-
-
-
0 x
2018 H2 SX/SE
-ZX10R Headers
-2016+ ZX10R Yoshimura Alpha 3/4 system
-Sprint P08 Filter
-Vcyclenut flash
-Driven block off plates
-Yager Werx Intercooler
-
Snakes709
- Supercharged!
- Posts: 1396
- Joined: Sun Aug 19, 2018 2:42 am
- Location: Edmonton, AB
- Bike(s): 2018 H2 SX SE
- x 11
- x 387
Re: Ecu modification
Your welcome
0 x
2018 H2 SX/SE
-ZX10R Headers
-2016+ ZX10R Yoshimura Alpha 3/4 system
-Sprint P08 Filter
-Vcyclenut flash
-Driven block off plates
-Yager Werx Intercooler
-
Champ87
- Supercharged!
- Posts: 1288
- Joined: Mon Apr 09, 2018 1:43 am
- Location: NW Indiana US
- Bike(s): Current bikes: 2018 H2 SX SE, '73 Yamaha RD350, '74 Kawasaki H1E, '74 Bultaco 250 Pursang
- x 301
- x 552
Re: Ecu modification
Here's where you connect to the ECU - the pic shows me installing the extra pin on one of the ECU connectors. If you're using the Woolich extension harness they will provide instructions when you buy.Drnick wrote: Fri Apr 19, 2019 1:20 pm No my tuner says one wire that has to be installed in a certain pin # on harness on connector on Ecu,then u route wire to back of bike for easy access. I just don’t know all the specifics
On this mod.
0 x
Champ87
It's amazing how fast you can go when you take your time.
-
Drnick
- Chirp-Chirp!
- Posts: 349
- Joined: Mon Apr 23, 2018 1:52 am
- Location: Pompano beach,Florida
- Bike(s): Too many to list!
- x 3
Re: Ecu modification
Didn’t realize I have to take front fairing off to do this wire install, but thanks for the info
0 x
Velocitus Eradicus
Who is online
Users browsing this forum: Google [Bot] and 79 guests
